WaterCheck™ RC
The Most Versatile Chlorine/Bleach Test Strip
- Easy to use strip test
- Residual and potency test in one
- Detection sensitivity about 0.2 ppm
- Quantitation range 0 0.5 1.0 and up to 500 ppm
- Residual and potency test, all in one step. 0 0.5 1.0 ppm chlorine, 1% bleach
Residual Chlorine test strips, similar to WaterCheck™ CP, except that WaterCheck™ RC strip will not react with peroxide. Therefore, it can be used in the reuse room in the presence of peroxide fume in the air.
About the Test:
Bleach chlorine solution is commonly used as a cleansing agent to disinfect medical instruments or equipments, such as dialysis machines. After the disinfection, chlorine is then rinsed off with deionized water or RO water before the instruments can be reused. The WaterCheck RC chlorine test strip provides an easy way to monitor the chlorine concentrations during the process of disinfection.
Product Features:
1. Fast and sensitive.
- Color reaction complete instantly to the chlorine in the sample.
- Detect residual chlorine to about 0.2 ppm
- Reacts primarily with chlorine, no reaction with peroxide until it is 100 ppm or higher.
2. Very consistent
- Consistent color reaction from lot to lot.
- Reliable results every time and all the time
3. Easy to read colors
- The strip color progresses from off white to very light green, green, blue, dark blue then to black/brown in response to less than 0.2 ppm trace to 500 ppm chlorine.
- Green, blue colors are very easy to read even under poor lighting condition.
4. Residual and potency strip in one
- The strip uses a dual indicator color system.
- It has very broad detection range, from trace to 500 ppm
- It turns blue/green at low chlorine levels, and blue/brown at high levels.
- It can be used as a residual strip or a potency strip for bleach/chlorine.
5. Long shelf life, stable at room temperature
- The dry strip is stable at room temperature.
- The shelf life is at least 2.5 years from the time of manufacturing.
Simple Steps to Use
The strip is primarily designed for use in hemodialysis disinfection control. However, it can also be used in different applications.
For disinfection of dialysis machines, bicarbonate mixing tanks or water distribution system, the final rinse water should have none or less than 0.5 ppm of residual chlorine according to the AAMI standards. The simple strip test can verify the compliance of the water quality.
- Collect the test sample in a clean cup from the sample port according to the manufacturer of the dialysis system.
- Dip the strip in the test solution for one second.
- For midstream sampling, wet the strip in the stream of test water briefly.
- Gently shake off the excess water.
- Compare the strip color to the color chart on the label.
- Any trace of blue/green color is an indication of the presence of residual chlorine.
How to Interpret the Test Results
Interpretation of the test results depends on the nature of the testing.
Using the qualitative method a one second dip-and-read test procedure, the strip can detect as low as 0.2 ppm of residual chlorine and will show a recognizable blue/green color. Any color for a qualitative test should be interpreted as a presence of 0.5ppm. Although the maximal allowable residual chlorine contaminant level in the rinse water is 0.5 ppm by AAMI standards, in practice, all rinse water in hemodialysis setting is tested negative with the strip. If tested positive, the rinsing should be continued.
If measurement of a more accurate chlorine level is desired, a 10 second test procedure should be followed by holding the strip under a slow running test water for 10 seconds and comparing the strip color with the color chart immediately. The strip color will be intensified at the end of 10 seconds. The length of the contact time of the strip with fresh test sample determines the final intensity of the strip color. The longer the contact time, the darker the strip color will be. The actual strip color may vary depending on how the test is done and the lighting condition of the room. The residual color blocks on the label are standardized with the 10 second test procedure.
Type of Samples
The strip is the most commonly used in detecting chlorine in water. However, the strip can also be used for detecting chlorine in other media, such as dialysate or bicarbonate solutions. In the blood, plasma or serum, chlorine will reacts with blood components such as ascorbic acid or other antioxidants, also with serum proteins and reduce the detectable chlorine level. What is detected in such media is the remaining of the chlorine rather than the initial level of chlorine contamination. In solvents or oil, the presence of chlorine can also be detected by the strip. However, the results should only be interpreted as qualitative.
How to Chose the Right Chlorine Test Strip for Your Specific Application
Since the test is based on the oxidative election transfer of chlorine molecules, chlorine will reacts to a variety of indicator system with different chemical properties. Because of this, not all the chlorine tests are created equal even when the same chemical indicator is used. They all differ in detection sensitivity, detection range, chemical specificity and thermal stability.
IBT offers three chlorine test strips for different applications. The following table compares the main features and the suggested applications of each strip.
Product Name Catalog Number |
Main Features
|
Suggested Applications
|
WaterCheck RC RC22101 |
Residual Chlorine / Bleach
0.2 ppm up to 500 ppm Not interfered by low level of peroxide. Not affected by peracetic acid in the air. |
Routine use for monitoring rinse water quality.
Comply with AAMI standards of 0.5 ppm or less. Verify 500 ppm Bleach Not recommended for 0.1 ppm chloramine testing |
WaterCheck CP CP20101 |
Residual Chlorine/Bleach
0.2 ppm up to 5000 ppm Equally sensitive for peroxide, peracetic acid. Sensitive to a broad spectrum of peroxides, chromate and other oxidants. |
Routine use for monitoring water quality
Comply with AAMI standards of 0.5 ppm or less for rinse water. Final check for dialysate contamination Best for broader protection of patient safety Not recommended for 0.1 ppm chloramine testing |
WaterCheck CM CM20201 |
Low Level Chlorine/Chloramine
Specially for detection of chloramine 0.1 ppm or less Comply with AAMI standards for purified water Detect both chlorine and chloramine |
Monitor carbon tank water purification loop.
Check to assure the acute mobile unit water quality of none or not more than 0.1 ppm of total chlorine |